Recently Completed Jobs by Politon

September 1, 2020 | Arlington, TX

This customer wanted to utilize us to install a new IT network throughout there facility. We installed a new IDF in the back of the warehouse with fiber going to an intermediate IDF in the middle of the building. The previous tenant had fiber ran through the warehouse so we ...

August 26, 2020 | Dallas, TX

We installed approximately 450' of 6 strands multi-mode armored cable between there main data room and a smaller data closet across the building. The materials for this project were Corning 1U rack mount fiber trays, Corning 6 strand bulkheads with LC duplex connectors. This Dallas fiber optic installation project was installed with ...

July 17, 2020 | University Park, TX

Once our tech got on site he discovered that the fiber was broken at the demarc box on the side of there house. The fiber was exposed coming out of the underground cable and into the demarc box. A landscaper snagged the exposed fiber and ripped it in two. Our ...

June 25, 2020 | Dallas, TX

We provided a fiber repair solution for an ST connector. When we arrived the customer decided to replace the ends on all 6 strands of multi-mode fiber because he was afraid the other strands had been damaged as well. Once the fiber was repaired over one hundred computers came back online. ...

June 24, 2020 | Crossroads, TX

We helped the customer move off of there old 1 Meg internet connection to there new 20 Meg Fiber Connection. This involved tracing down there old AT&T modem and patch cord that fed their network switch and patching in the network switch to the new fiber modem. Once the new modem ...

April 29, 2020 | Fort Worth, TX

This installation of data cabling in Fort Worth was so we could install wifi access points in the ceiling over there procurement area. Each time the customer pulls an item off the shelf they scan the item and it updates there database on inventory and order fulfillment. The scanners they ...

April 29, 2020 | Fort Worth, TX

We were asked to extend the demarc from the customer's demarc room to there data rack in the next room. Our tech utilized Cat 6 cable for the installation and ran it through the ceiling space. We utilized male RJ45's ends on both ends of the cable. After the Category 6 ...

April 16, 2020 | Roanoke, TX

This customer had a very unique situation for us to solve. The owner of a very large business park wanted to have wifi in his RV on the back of his property. Since he travels the country most of the year when he is here to check on his business ...

April 9, 2020 | Euless, TX

Our solution consisted of two NanoBeam AC Gen 2 Bridges and two Ubiquiti Ethernet Surge protectors. We mounted the Nano Beams on 1.5" pipe and fastened the surge protector with a self-tapping screw to the pipe through a previously drilled pilot hole. We used 14 gauge ground wire with a crimp-on connector to ...

April 7, 2020 | Richardson, TX

Golds Gym contacted us to repair or replace their emergency phone in their pool area at there Richardson TX location. We went on-site to discover there old emergency pool phone was rusted and corroded. We took the old one out, tested the phone line, cleaned the wall and installed the ...

March 11, 2020 | Cedar Hill, TX

We went on-site to troubleshoot the network cabling at this Cedar Hill, TX facility. When we arrived we discovered several problems with why the TVs would not get a network connection. There was a few TVs that had there network connection plugged into the telephone jack so that was an ...

March 7, 2020 | Mesquite, TX

We went on-site and determined this was basically two network cabling projects. The easier project was the Cat 6 cabling that would be running to the IDF cabinet at one end of the building. This IDF was connected back to the main data room with OM3 multimode fiber optic cabling. The ...

March 6, 2020 | Dallas, TX

We provided a turn-key projector installation solution for Smart City Apartment Locators. We provided a universal Epson projector mount which is a really solid universal mount. We had to utilize a one-man bucket lift to mount the projector on the ceiling with a super strut. We spanned two joists with ...

March 2, 2020 | Arlington, TX

We installed Cat6 data cabling to all of there new offices in Arlington, TX. The customer wanted to reuse there own data rack which posed a few challenges since they did not have all the nuts and bolts so we improvised until we got them. This is usually the case ...

February 19, 2020 | Fort Worth, TX

We installed a wifi solution in Fort Worth, TX for a Locus Robotics project. This project required custom painted backboards for the wifi Ap's, Cat6 dual wire runs to each wifi access point, fiber optic cabling between two separate IDF cabinets, UPS installation and mounting customer provided switches. In layman's ...